Видео

great

Best video using Government methods of finishing the stock. What brand Linseed Oil do you use?

Are you abls to shoot those out of a shotgun that is meant for normal smokless powder?

The over shot card will interfere with the shot pattern causing blown patterns.

Good grief. This is so simple even I can do it…and will! Pyrodex is much cheaper than smokeless powder and I’m doing a lot of shotgun hunting these days. Thanks for the video!

It’s not a rifle but shooters skill. I would use these rifles instead of any army’s standard issue sniper rifle

Good review. I have a M22 and it shoots too far to the left. Used up all the adjustments. Suggestions? I love it otherwise.

Can I share this in my video? Previously, I was looking for instructions on how to disassemble the rear sight of the G&G 98K airsoft rifle because mine doesn't use a hammer to tap the pin. No one had made a video about it, so I started looking for a real firearm disassembly video and then I found your video. Finally, I managed to take out the rear sight. Thank you.🤣

Talk less n work more

Is the paper quality very good? Better than newspaper quality?

Yo man you didn't even talk about the type-2 phaser wtf.

LOL! That’s great! And now McDonalds will start marketing this because of your video!

I need to start production

Co bán ko ban

The best accuracy improvement for the SKS is better ammo. I'm interested in bedding the stock to prevent splitting over time.

Do they not sell this anymore?

I watched this video years ago. I have a lot lot more experience loading blackpowder muzzleloaders and making blackpowder buckshot. So, looking at it again with fresh and experienced eyes, this video is very very good for making blackpowder shotgun shells. Very good job sir.

Using a hammer to seat the primer would make me a bit nervous. If you have a drill press you can use that to press in the primer and compact the powder.

Most funniest part was the pink matching reloading equipment lol 😂😂😂

this is a great scope, great review. thank you.

I'm happy to see I'm not the only one that wipes down their guns with old clothes. The old PJs was cracking me up.

best glue is clear nail polish from the dollar store. it even works on full brass shells. you can even use different colors to represent different loads.

It seems to be the 8mm-06, vaguely. You know, the wildcat cartridge.

How do you have a scope with 2 feet of eye relief???? Never heard of that

209 primers are hard to find in my area. Would Federal 209A work?

Here I am listening intently... Then I here Overweighty.... Then I'm like OMG a few British Columbian lol

Jerichos SUCK and have a grainy loose trigger and slide movement

From a Canadian to obviously another Canadian thanks very informative

If one chooses Tung oil, make absolutely sure it's 100% Tung oil. Many products marketed as Tung oil actually contain very little, you will be disappointed if you use such a product, I speak from experience.

I've had five Enfields, 4- No.1's and 1 No.4, ALL the front sights were offset to the right side of the dovetail except one that a centered front sight yet had all indications of being refurbished (Lithgow manufactured 1917, butt stock stamped 1942). When I fired the Lithgow specimen, sure enough, I had to drift the front sight to the right to acquire 'zero', it must be inherent in the SMLE's OR all my Enfields suffered from offset stock-bedding.

I am a retired painter, solvent-based wood stain wiping rags are also notorious for spontaneous combustion, Whenever we did a large oil staining project, at day's end, we would hang the stain-soaked rags in a single, flat layer on any horizontal surface we could utilize to dry overnight. Once the rags were dry, stiff and relatively odor-free, we would discard them. In our area, years ago, a church congregation gathered to stain newly installed woodwork, they tossed their wet stain-soaked wiping rags in brown paper shopping bags at the end of the day, the church burned down overnight due to the rags catching fire.

You can use a roll crimp or even a crimp starter.

How build the powder black?

Good video thanks.

Great video dude!

There are custom made handgrips that cost between $2K to $13.5K depending on the pistol you choose!

I'LL TAKE THE WARHAMMER!

A roll crimp would have been nice. But, the tool would have been expensive.

Not... Dead... Yet...

What kind of glue did you use? Ive dont basically the same thing as you and never had a problem. Infact, I still have some left that i loaded a decade ago ..

Have u ever used wax to substitute the glues

I see in the comments you have been corrected but continue to instruct reversed polarities I collect and restore cast iron cookware, The positive (anode) goes to the sacrificial piece of iron, and the negative (cathode) goes to the item you want the rust removed from. Restoring cast iron cookware, because it will be re-seasoned in a 400 degree oven for 1 hour, will not have any issues with hydrogen embrittlement. By no means am I an expert. However, if I processed a rifle barrel with electrolysis I would seriously consider doing a similar process in the oven before shooting. Barrel Rockwell hardness is low but a still, it is a subject worth doing some research on before pulling the trigger.

For the occasional thrill of holy black, all this works, but in the long run, and to have nice shells that are correct and presentable, a roll crimper is the way to go. BPI roll crimpers are a rip-off. I took the brass crimper wheel out of an old hand roll crimper and use it in drill press. Other roll crimpers are good too, from different makers, but the BPI ones are pretty much a rip-off.

Distance that bullet

Can't argue with the results.

How can I get reloading device online

Question: My M1 has overdone furniture varnish on it, any suggestions on how to get it off?

Watching and listening from pinas garita San Enrique iloilo.

Looks like most of my shooting buddy's rooms...as well as mine. Hope it turned out well. Would like to see a video about your M48 Mauser.

Pleas post a video regarding reloading of rifle & revolvers.